Connecting a pigtail to an access point can be extremely easy, if you have a pigtail with the proper connector, and if the access point manufacturer designed the antenna for easy removal.
Linksys access points, for example, have easy-to-remove antennas. The difficulty of finding the proper connectors argues for buying rather than building pigtails.
WY016-04.qxd 6/1/04 10:20 PM Page 92 Quark08 Quark08:Books:PQJobs:WY016/Wi-Fi:printer_corr:
93
Chapter 4 — Modifying Your Access Point
Linksys Makes It Easy
If you have a Linksys WAP11 or BEFW11S4 access point, connecting your high-gain antenna to the access point is a snap, because these Linksys access points have detachable antennas.
(Here’s where your opposable thumb comes in). Just grip the antenna base firmly between thumb and forefinger and turn counter-clockwise to remove. (See Figure 4-12.)
Other access points may not be so easy. We recommend an access point with external connec- tors and detachable antennas, because otherwise you may have to open up the access point, dis- connect the existing antenna wires, and solder a new connector onto the wires—undoubtedly voiding any warranty in the process. Figure 4-13 shows a hard-wired antenna in a Cisco access point.
The FCC Makes It Hard
The other area where you might run into a slight hiccup is in building a pigtail to connect the access point to the antenna cable. The antenna side of the pigtail is no problem: Your antenna cable probably has standard female N-Connectors. So, to make the connection, the pigtail needs to have a standard, easy-to-find male N-Connector.
FIGURE4-11: The Linksys configuration program: Advanced section, Wireless tab, Antenna Selection menu.
WY016-04.qxd 6/1/04 10:20 PM Page 93 Quark08 Quark08:Books:PQJobs:WY016/Wi-Fi:printer_corr:
94 Part I — Building Antennas
FIGURE4-12: Removing the original antenna.
FIGURE4-13: Cisco access point with a soldered antenna connector.
WY016-04.qxd 6/1/04 10:20 PM Page 94 Quark08 Quark08:Books:PQJobs:WY016/Wi-Fi:printer_corr:
The male connector has a pin in the middle. The female connector has a socket. In addition, male connectors have threads on the inside of the connector body, while female connectors are threaded on the outside. (See Figure 4-14.)
The problem stems from the connector on the access point. The FCC mandated weird connec- tors for Wi-Fi antennas, because they were afraid that hobbyists would do things like connect- ing high-gain antennas to access points and possibly jack-up the power of their wireless networks beyond the legal limit. (Why would anybody want to do that?) They didn’t make it illegal to hook up a high-gain antenna, but they did try to ensure that you would use only antennas specifically designed for the wireless system. They did this by specifying connectors that you couldn’t find in your local Radio Shack, and which are incompatible with standard antenna connectors.
Linksys, for example, satisfies the weirdness requirement with reverse polarity (RP) TNC con- nectors. At first glance, Reverse Polarity (also called “Reverse Gender”) connectors look like normal male and female connectors. On closer inspection, however, you’ll find a major differ- ence: The male connector has a socket, and the female connector has a pin. The Linksys access points, for instance, have Reverse Polarity female connectors (female body with a pin), so the
95
Chapter 4 — Modifying Your Access Point
FIGURE4-14: Standard male connector (left) and standard female connector (right).
WY016-04.qxd 6/1/04 10:20 PM Page 95 Quark08 Quark08:Books:PQJobs:WY016/Wi-Fi:printer_corr:
96 Part I — Building Antennas
pigtail has to have a Reverse Polarity male (male body with a socket). Figure 4-15 shows RP-TNC connectors.
Another common example is the reverse polarity SMA connector used on many D-Link prod- ucts. Figure 4-16 shows RP-SMA connectors.
Don’t confuse RP with Reverse Threading (RT), which apparently also satisfies the weirdness requirement, and which refers to male bodies threaded to turn counter-clockwise to tighten, unlike normal male bodies, which turn clockwise to tighten.
The FCC’s desire to thwart users wishing to attach standard antennas to Wi-Fi equipment has been less than entirely successful. However, the weirdness requirement has created a thriving pigtail industry, which you will now be supporting with a modest purchase (assuming you fol- low the advice in the next paragraph).
In Chapter 1, we recommended purchasing pre-configured pigtails for wireless client adapters, because of the hassle of soldering the tiny connectors needed to fit PC card connections.
Buying pigtails is the easy way to go for access points as well. There aren’t any tiny PC card connectors to deal with. But you would probably have to special-order the RP connector for the pigtail anyway, so why not just go ahead and special-order the pigtail itself?