Tài liệu Fundamentals Of Power Electronics P2 pptx

... factor) definition of, 546-550 of bridge rectifier, single phase, 566 of peak detection rectifier, 548-550 of phase-controlled rectifier, three phase, 573 Power sink element (see Power source element) Power ... 279-282 inverted forms, 272 of real pole, 266-268 of real zero, 269 of RHP zero, 270 Phase control of resonant converters, 659 of three-phase rectifiers, 570-575...

Ngày tải lên: 13/12/2013, 01:15

... http://ece-www.colorado.edu/~pwrelect/book/SecEd.html (6 of 6) [25/04/2002 16:42:05] Fundamentals of Power Electronics Fundamentals of Power Electronics Second Edition Up To instructors of Power Electronics courses: how to ... (1 of 2) [25/04/2002 16:42:07] Fundamentals of Power Electronics http://ece-www.colorado.edu/~pwrelect/book/copies.html (2 of 2) [...

Ngày tải lên: 13/12/2013, 01:15

... display) Fundamentals of Digital Electronics 10-6 © National Instruments Corporation Lab 10 Seven-Segment Digital Displays Notes © National Instruments Corporation 11-1 Fundamentals of Digital Electronics Lab ... XOR Gate Clock QDQDQDQDQD QD CCCCCC 12 4356 Fundamentals of Digital Electronics March 1998 Edition Part Number 321948A-01 Fundamentals of Digital Electronics...

Ngày tải lên: 13/12/2013, 01:15

... considered to be the ability of the material to absorb energy in the plastic zone. The measure of toughness is the amount of energy absorbed after being stressed upto the point of fracture. (i) Creep- ... • Types and uses of some common non-ferrous metals. • Types and uses of some non-metals. • Important mechanical properties of materials. 1.2.1 Introduction Choice...

Ngày tải lên: 17/12/2013, 11:15

... or manufacture a product range. The range of operational speeds of a machine or the range of powers of a typical machine may be also as per a series of preferred numbers. Version 2 ... other, the nature of fit is dependent on the limits of tolerances and fundamental deviations of the mating parts. The nature of assembly of two mating parts is defined by three...

Ngày tải lên: 17/12/2013, 11:15

... weeks, depending on the layout of the office, the state of the cable raceway system, and the availability of a long enough patch cord (see Figure 13). Fundamentals of Fiber Cable Management Interconnect ... splices with any combination of OSP fiber counts, allows flexibility in the selection and routing of OSP cables. Fundamentals of Fiber Cable Management On-Frame and Off-F...

Ngày tải lên: 21/12/2013, 07:16

... strains may be derived in terms of these displacements. 2.3.2 Normal strains Consider an element AB of length δx ( figure-2.3.2.1). If displacement of end A is u, that of end B is u u x ∂ +δ ∂ x ... discussed. 2.3.9 Reference for Module-2 1) Mechanics of materials by E.P.Popov, Prentice hall of India, 1989. 2) Mechanics of materials by Ferdinand P. Boer, E. Russel...

Ngày tải lên: 25/12/2013, 23:18

... minimum value of H f occurs at a ratio of recess radius to bearing radius R 0 IR of 0.53. All bearing-pad configurations exhibit minimum values of H f when their ratios of recess ... support the load. The load capacity is independent of the motion of bearing surfaces or the fluid viscosity. There is no problem of contact of the surfaces at star...

Ngày tải lên: 27/01/2014, 16:20

... arises in many, if not most, of the computational problems of manu- facturing, due to the inherent geometrical nature of form design, of manufacturing processes, and of the physical products themselves. ... differences of simple geometric bodies. A complex problem reduces to a series of zones involving the combination of simple shapes. Combinatorial geometry is the study of...

Ngày tải lên: 21/02/2014, 22:20

... range of a linear transformation L of U into V is the set of vectors v of V into which some vector u of U is mapped, i.e., the range of L is defined as the set of v = Lu, for every vector u of U.Thekernel ... position and orientation of the vehicle body. As a matter of fact, the control of rolling robots bears common features with that of the redundancy resolution of...

Ngày tải lên: 19/01/2014, 18:20