Marine Structural Design Episode 11 doc

... actual reduce its viscosity, and vice-versa. As a result of the varying properties of marine fuels, often within one tank, actual viscosity must be continuously measured and

Ngày tải lên: 13/08/2014, 16:22

... aluminium alloys Die design Process control 111 Modification of the diecasting process 113 Applications of diecastings 114 The diecasting foundry 114 Die coating 116 10 Low pressure and ... Surrey, RH1 1QS. Foundry Management & Technology, 110 0 Superior Avenue, Cleveland, OH 4 4114 , USA. Foundry & Technical Liaison Ltd, 6 -11 Riley Street, Willenhall, West Midlands,...

Ngày tải lên: 13/02/2014, 16:20

... of marine structural design have been developed: Level 1: Design by rules Level 2: Design by analysis Level 3: Design based on performance standards Until the 1970’s, structural design ... combinations is the first step in marine structural design. For structural design and analysis, a structural engineer needs to have basic concepts of waves, motions and...

Ngày tải lên: 14/03/2014, 16:20

... Power-Efficient Gathering in Sensor Information System, 2002 IEEE Aerospace Conference, vol. 3, pp .112 5 -113 0 [9] X. Bao, D. J. Webb, and D. A. Jackson (1993). 32-km distributed temperature sensor ... management, and data dissemination protocols have been specifically designed for WSNs where energy awareness is an essential design issue. Among them, routing protocols might differ d...

Ngày tải lên: 20/06/2014, 12:20

... cycles which cannot be expressed in this way, e.g. ε = ε av +diag(ε ampl 11 sin(ωt + ϕ 11 ),ε ampl 22 sin(ωt + ϕ 22 ), 0) ϕ 11 = ϕ 22 (2.77) and which require individual time tracking f ij (t)ofvariousε ij components. The ... (out-of-phase cycles (= OOP) and b) the open-curve cycles is of importance 2.5 Geotechnical Aspects 111 σ v0 σ h0 = K 0 σ v0 traffic loading σ v σ h τ σ v σ v...

Ngày tải lên: 01/07/2014, 10:43

... of concrete can be found in Auberg [69]. RILEM TC 117 FDC recommends the CDF test 1 [732] for determining deicing salt resistance and RILEM TC 119 recommends the CIF test 2 [729] for frost resistance. ... [%] 0,0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0 Moisture uptake [kg/m²] 1 cm 2 cm 3 cm 5 cm frost suction 40 50 60 70 80 90 100 110 40 50 60 70 80 90 100 110 Moisture [%] RDM [%] 1 cm...

Ngày tải lên: 01/07/2014, 10:43

... approximation of state variables shape function N 11 derivative N 11 ;1 N 4 2 (ξ 2 ) N 2 1 (ξ 1 ) N 11 (ξ 1 ,ξ 2 ) ξ 2 ξ 1 ξ 2 ξ 1 N 4 2 (ξ 2 ) N 2 1;1 (ξ 1 ) N 11 ;1 (ξ 1 ,ξ 2 ) ξ 2 ξ 1 ξ 1 Fig. 4.4. ... 393 N 1 N 2 N 3 N 4 N 5 N 6 N 7 N 8 E 1 E 2 E 3 E 4 E 5 E 6 E 7 E 8 E 9 E 10 E 11 E 12 F 1 F 2 F 3 F 4 F 5 F 6 ξ 1 ξ 2 ξ 3 Fig. 4 .11. 3D-p-element: definition and numbering of elem...

Ngày tải lên: 01/07/2014, 10:43

... ˆu 1 u 2 +ˆu 2 ⎫ ⎪ ⎬ ⎪ ⎭ (4.159) and for the stresses σ = σ I + σ II = 1 2 ⎧ ⎪ ⎨ ⎪ ⎩ σ 11 +ˆσ 11 σ 12 − ˆσ 12 σ 21 − ˆσ 21 σ 22 +ˆσ 22 ⎫ ⎪ ⎬ ⎪ ⎭ + 1 2 ⎧ ⎪ ⎨ ⎪ ⎩ σ 11 − ˆσ 11 σ 12 +ˆσ 12 σ 21 +ˆσ 21 σ 22 − ˆσ 22 ⎫ ⎪ ⎬ ⎪ ⎭ (4.160) The ... crit2, Q1SPs, tolerr=0.0001) dF=2.5 dF=5.0 dF=10.0 dF=20.0 dF=30.0 dF=60.0 40 50 60 70 80 90 100 110 120 130 140 150 -3500 -3000 -2500 -2000 -1500 -...

Ngày tải lên: 01/07/2014, 10:43

... for the reduction of unloaded subsystems, as proposed by [313], accurate results. Additionally [111 ] mentions that the difference in the reduction quality of reduced linear total systems between ... inter- faces have been developed within the scope of reduction methods for large structural dynamic models and the design of single dynamical components of challenging structures. These method...

Ngày tải lên: 01/07/2014, 10:43

... Load-Independent Environmental Impact 99 -20 -15 -10 -5 0 5 10 15 20 8 .11 10 .11 12 .11 14 .11 16 .11 18 .11 20 .11 22 .11 24 .11 26 .11 28 .11 Days Temperature [°C] 0 1 2 Percipitation [l/m²] percipitation air ... 3,50E-03 3,60E-03 3,70E-03 3,80E-03 1/T [K -1 ] ln (R) 0.7cm 8 .11- 10 .11 0.7cm 10 .11 0.7cm 11. 11 0.7cm 15 .11 0.7cm 16 .11 3.4cm 10 .11- 16 .11 T >0 o CT...

Ngày tải lên: 01/07/2014, 11:20