Handbook Corrosion (1992) WW Part 12 docx

... verifying compatibility under the particular design conditions used by his fluid system. Control of Stress Corrosion. The subcontractor was required to prepare a stress -corrosion plan utilizing MSFC ... sustained stress levels on the part below stress- corrosion threshold levels, especially in the more susceptible short-transverse grain direction • Protect the part from the detri...

Ngày tải lên: 11/08/2014, 04:21

... articles on general corrosion, localized corrosion, metallurgically influenced corrosion, mechanically assisted degradation, and environmentally induced cracking. More than 20 distinct corrosion mechanisms ... Section, methods of corrosion testing and evaluation in the laboratory as well as in-place corrosion monitoring are discussed. For each major form of corrosion (pitting, st...

Ngày tải lên: 11/08/2014, 04:21

... intergranular corrosion. Isolated carbides that persist from high temperatures will not affect corrosion behavior. Intergranular Corrosion and Other Forms of Corrosion. Susceptibility to intergranular corrosion ... corrosion, such as pitting or general corrosion. The environments that cause intergranular corrosion for a particular alloy system are often very specific. Susceptib...

Ngày tải lên: 11/08/2014, 04:21

... Handbook on Corrosion Testing and Evaluation, W.H. Ailor, Ed., John Wiley & Sons, 1971, p 291-366 110. W.E. Berry, Testing Nuclear Materials in Aqueous Environments, in Handbook on Corrosion ... with the Aluminum Association), in Corrosion in Natural Environments, STP 558, American Society for Testing and Materials, 1974, p 99-113 12. B.W. Lifka, Corrosion Resistance of A...

Ngày tải lên: 11/08/2014, 04:21

... 11 of ASM Handbook, formerly 9th Edition Metals Handbook contains information on abrasion and wear. Other Forms of Corrosion. Selective leaching, also known as dealloying or parting corrosion, ... National Association of Corrosion Engineers 3. Corrosion Data Survey Metals Section, 6th ed., 1985; Corrosion Data Survey Nonmetals Section, National Association of Corrosion Engin...

Ngày tải lên: 11/08/2014, 04:21

... Application °C °F pH Corrosive medium Bathtubs To 49 To 120 5-9 Water, cleansers To 100 To 212 12 Alkaline solutions To 100 To 212 1-2 All acids except hydrofluoric Chemical ware 175-230 ... allows the parts to be handled more easily. Parts are either air dried or dried with radiant or convection dryers. Convection drying consists of gradual heating of the parts to 120 °C (250 ....

Ngày tải lên: 11/08/2014, 04:21

... variety of corrosion problems can be encountered in the drilling and primary production of oil and gas. These include weight loss corrosion, pitting corrosion, corrosion fatigue, stress -corrosion ... ASM Handbook, formerly 9th Edition Metals Handbook. Finally, fracture characteristics of alloy steels are reviewed in Fractography, Volume 12 of ASM Handbook, formerly 9th Edition...

Ngày tải lên: 11/08/2014, 04:21

... Report FHWA/CA/TL80 -12, California Department of Transportation, 1980 119. T.E. Wright, The Corrosion Behavior of Aluminum Pipe, Mater, Perform., Vol 22 (No. 12) , 1983, p 9 120 . W.C. Cochran, ... Aqueous Corrosion of Aluminum, Part 2 Methods of Protection Above 200 °C, Corrosion, Vol 12 (No. 10), 1965, p 480t 99. D.W. Sawyer and R.H Brown, Resistance of Aluminum Alloys to F...

Ngày tải lên: 11/08/2014, 04:21

... Grade 12 58 Boiling nil Ammonium hydroxide Grade 12 30 Boiling nil Grade 12 10 Boiling nil Grade 7 10 100 <0.025 Aluminum chloride Gade 7 25 100 0.025 Ammonium chloride Grade 12 10 ... nil Source: Ref 8, 26, 67, 80, 85, 86, 109, 127 Appendix 2: General Corrosion Data for Titanium Alloys This appendix is a compilation of general corrosion rate values for commercia...

Ngày tải lên: 11/08/2014, 04:21

... steel is used for parts subject to atmospheric corrosion or salt spray and for parts that will be lacquered or painted. Phosphate treatment increases corrosion resistance markedly, particularly ... (120 0 °F), molten tin reacts with water vapor to form SnO 2 and hydrogen. From 25 to 100 °C (75 to 212 °F), hydrogen sulfide (H 2 S) has little apparent effect on tin, but above 100 °C ( 2...

Ngày tải lên: 11/08/2014, 04:21